JXK-CR-002

The infrared steering remote control is designed specially to keep you enjoys music; at the same time protect your safety when driving. You can copy function of other common remote control which you use in car to this steering remote control and then install it to your car steering wheel, so it can be used instead of your common remote control.   The steering remote control applies to car CD, car DVD, car GPS, car MP3, and other car electronic products.

Applicable locations:

in 12V 24V cars /in 24V  lorries/ in 24V trucks,fixed (lamped) on  your car's front windshield

Applicable people:

12V 24V car drivers/12V 24V lorry drivers/12V 24V truck drivers,

hackie/taxi driver/taximan/cab driver/bus driver

1Copy button (KEY1~7)

2Start Copy/Save button

3LED Indicator for copy state

4infrared remote control window

5lock button for install

6Steering wheel fixed socket

7Copy button (Key 8~9, Print as VOL+/VOL- button)

Operation Directions

The products must copy code of remote control which you want to replace, then can use normally, or all buttons will not work.

Copy steps:

---Press "SET" button

---red indicator lights continually

---Make remote control which is copied aim at the transmitting window of replicableremote control

---Press copy button of replicable remote control (the indicator becomes slow glinting)

---press button which need be copied on former remote control (the indicator will glint thrice rapidly then becomes to light continually) 

---Operate above two steps repeat

---Press "SET" button to save after finishing copy(The indicator goes out)

Detailed Operation

1 Firstly check if remote control which need be copied can work normally.

2 Copy operation (for example, copy" " button)

2.1 Press and hold on "SET" button about 2-3 seconds to come learning mode, LED indicator lights continually (the indicator will go out if no press any button within 15 seconds)

2.2 Press and hold buttons on replicable remote control for a while, for example, printed"" button, the indicator will glint slowly and replicable remote control enters copying and receiving signal mode. On this mode, take remote control which need be copied and make distance of two remote control windows at 1-2CM face to face, as following picture:

2.3 When the indicator light is glinting slowly, press and hold on corresponding " " button on the remote control which need be copied, after about 3 seconds,  the LED indicator glints thrice rapidly then comes light continually. This shows copy successful. And red indicator will keep light continually, comes to mode again that wait copying and receiving.

2.4 For copying function of other buttons, operation is same with 2.2 and 2.3.

2.5 After finishing copy, press "SET" button to save operation and quit, the indicator goes out, copying is finished.

Illustrate

1. Buttons is printed according to usual printing of car CD/DVD remote control, only for your reference. Factual buttons function is only related to buttons function which is copied. For example, if  button on steering remote control copied function of "VOL+" button on the remote control which is copied, so the button has "VOL+" function.

2. The products can be erased repeatedly. If you have copied buttons of certain remote control, when you copy buttons of another remote control again, old function will be cleared and covered automatically.

3. After finishing copy, PLS operate you car electronic products by using replicable remote control, and check if all buttons function is copied usefully. If certain button can't use normally, PLS copy repeat for the button one or twice.

4. During copy, copied button must be pressed and hold on till the indicator glints rapidly thrice then becomes light continually, at this time copied button can be loosened.

5. During copy, if the indicator glints unconventionally, it shows operation is not successful. PLS copy again.

Installation Instructions

Step 1:

Step 2:

step 3:

The buttons are different from JXK-CR-002,But the way of Installation is the same.

Battery

Before using the remote control, first to remove the battery's isolation slice. 
Battery capacity is too low or depletion will affected the normal using of remote control or not working, you'd better remove the battery cover to replace the same type battery